Audient ASP2802 Specifikace

QUICK START GUIDEVersion: 1.00

Page -10-© Audient LtdControl Surface PanelControl Surface InstallationPlease refer to the separate DAW specific control surface manuals found online

Page -11-© Audient LtdRear Panel Channel Connections

Page -12-© Audient LtdDB25 Wiring SpecificationThe following table provides channel counts for each DB25 connector:Summing Input DAW Inputs DIRECT Out

Page -13-© Audient LtdRear Panel Master Connections

Page -14-© Audient LtdDAW Ethernet Connection (Mac)You can use standard Cat-5e Ethernet cable to connect ASP2802 to your studio DAW computer. The inte

Page -15-© Audient LtdNetworking (Mac)Once you have connected ASP2802 to your studio computer via either a direct Ethernet link or through a router an

Page -16-© Audient LtdNetworking (Mac)Moving across to ASP2802, power up the console and once booted, press the SETUP button. The OLED displays will s

Page -17-© Audient LtdNetworking (Mac)Subnet Mask set to 255.255.255.0:Port set to 1212:Press the setup key to exit setup and your setting will be sav

Page -18-© Audient LtdNetworking (Mac)Your console should now be connected to your studio DAW computer and ready for configuration as a HUITM control

Page -19-© Audient LtdDAW Ethernet Connection (PC)You can use standard Cat-5e Ethernet cable to connect ASP2802 to your studio DAW computer. The inter

Page -2-© Audient LtdASP2802 Installation... Page 3 Warning 3 Safety & Ma

Page -20-© Audient LtdNetworking (PC)Once you have connected ASP2802 to your studio computer via either a direct Ethernet link or through a router and

Page -21-© Audient LtdNetworking (PC)In the Local Area Connections properties dialogue window scroll down and select Internet Protocol TCP/IP and then

Page -22-© Audient LtdNetworking (PC)Moving across to ASP2802, press the SETUP button. The OLED displays will show the first page of console setup.Fir

Page -23-© Audient LtdNetworking (PC)Subnet Mask set to 255.255.255.0:Port set to 1212:Press the setup key to exit setup and your setting will be save

Page -24-© Audient LtdNetworking (PC)Your console should now be connected to your studio DAW computer and ready for configuration as a HUITM control s

Page -25-© Audient LtdNetworking (PC)You will most likely be running DHCP with automatic IP hand out.Ensure that the console is set to use DHCP on the

Page -26-© Audient LtdExample SystemsExample System 1 - 8 Channel DAW PlatformThe first example system shown on the next page illustrates abasic syste

Page -27-© Audient LtdExample SystemsExample System 3 cont.If you wish to work it another way, an all analogue, zero-latency monitor mix could be form

Page -28-© Audient LtdExample System 1

Page -29-© Audient LtdExample System 2

Page -3-© Audient LtdInstallation

Page -30-© Audient LtdExample System 3

Page -31-© Audient LtdExample System 4

Page -32-© Audient LtdBus Compressor Settings

www.audient.comAudient Ltd1 Stable CourtHerriard ParkHerriardHampshireRG25 2PLUKPhone: +44 (0) 1256 381944Fax: +44 (0) 1256 381906

Page -4-© Audient LtdInstallationPackage ContentsYour ASP2802 Console has been carefully and meticulously tested and inspected before dispatch.Please

Page -5-© Audient LtdInstallationASP2802 Dimensions (including rubber feet)Height Front - 60 mm Height Rear - 170 mmWidth - 450 mmDepth -

Page -6-© Audient LtdInstallationVentilationCare should be taken not to obstruct the series of ventilation holes in the metalwork of the console. The

Page -7-© Audient LtdRack Installation (optional)Please note that rack ears for ASP2802 are an optional extra.

Page -8-© Audient LtdChannel Strip

Page -9-© Audient LtdMaster Section